|
|
Four important indexes determining the application effect of talc in plasticsTalc has a significant reinforcing effect on molecular compound plastics, but not all talc products have reinforcing effect. The strengthening effect is very obvious with the difference of product grade. It is difficult to put forward a unified and specific standard for talc powder used in molecular compound plastics industry. The general principle of plastic properties is: try to use pure talc products with appropriate particle size, the finer the products, the better. The raw material source of talc must be stable, the grade of the product, especially the particle size distribution, and the wet whiteness and hue must be stable and continuous. In view of the diversity of talc, it needs the technical support of manufacturers to achieve the best results. When selecting products, at least the "four degrees" of talc itself should be considered, that is, purity, whiteness, flake and fineness Generally speaking, the above four factors should be considered at least when evaluating a talc product. It is one-sided and incomplete to judge quality only by one index. If someone only uses the average particle size to judge the quality of talc products, it is very questionable. One purity Purity refers to the content of talc in the product. Talc contains impurities in nature and industrial production, and 100% pure talc in industry is impossible to exist. There is no doubt that the higher the purity of talc, the better the strengthening effect. The results show that some impurities in talc not only reduce the purity, but also have a significant impact on the performance of the final product. The carbonate, metallic iron and heavy metals in talc have a very bad effect on the aging resistance and thermal stability of molecular compound plastics. Chlorite content has little effect on aging resistance and thermal stability. In China, talc belongs to carbonate talc type, so carbonate should be removed as much as possible in mineral processing, and talc raw materials with low iron and heavy metal content should be selected to produce talc powder of molecular compound plastic grade. The purity of the main talc deposits in Liaoning, Shandong and Guangxi is relatively high. After screening, the purity can reach 96-98%. It is the most suitable talc raw material for modified molecular compound plastics in the world. However, carbonate, iron and heavy metals in the products of different manufacturers in different regions and the same region are quite different. At present, most of these high-purity minerals are for export, and there is little demand in China except for some joint ventures and wholly-owned enterprises. The content of talc in domestic market fluctuates between 20-98%. The products with low talc content have very limited strengthening effect on molecular compound plastics, and mainly play the role of general fillers. However, if the content of carbonate and iron and heavy metals is high, it will cause the aging resistance and thermal stability of the products of molecular compounds. XRD + phase analysis is recommended to distinguish the purity of talc for scientific research, and the deviation is within 5%. In production, the purity of talc (except chlorite talc type) can be estimated by detecting the loss on ignition. Generally speaking, products with loss on ignition less than 8.0% are more suitable for molecular compound plastics as reinforcing fillers, and the best loss on ignition is less than 6.5%. Two whiteness There are two kinds of whiteness in talc test: narrow sense and broad sense. The narrow sense of whiteness is the general definition of whiteness, which can be expressed by blue light whiteness R457, y, L *, Ganz plastic characteristic whiteness and Hunter whiteness. There are no less than 100 formulas for calculating whiteness in the world, and no less than 10 formulas are often used in non-metallic mining and light industry. Using different instruments, different calculation methods will get different results. The national standard GB / T 5950 specifies the measurement method and calculation formula of the whiteness of talc. This standard adopts the International Commission on illumination (CIE) 1964 supplementary standard chroma system and standard illuminant D65 specified in gb3977 to calculate the whiteness with three constant stimulus values and chromaticity coordinates; adopts CIE LAB uniform color space specified in gb7921 to calculate the hue, chromaticity and color difference with lightness index and chromaticity index. The method is as follows: when the whiteness of the ideal complete reflection diffuse body with 1 spectral reflectance is 100, and the whiteness of the absolute black body with 0 spectral reflectance is zero, the three extraordinary stimulus values of the sample are measured under the conditions specified in this standard, and then the whiteness is calculated by the formula specified, and the hue angle, chromaticity and color difference between the samples can be calculated. Generalized whiteness includes dry whiteness, wet whiteness and hue. The said wet whiteness is the whiteness measured after adding appropriate amount of DMP (dimethyl phthalate) into talc plastic properties. For the same raw material, the finer the particle size, the higher the whiteness. The higher the moisture content, the lower the whiteness. Although the whiteness has no effect on the physical properties of products, it is very important to keep the purity of color for light color products. One of the disadvantages of talc is that the color of molecular compound plastics is more or less darkened after mixing, which is an important factor limiting the wide application of talc in molecular compound plastics. Through the measurement and comparison of dry whiteness and wet whiteness, the darkening extent of molecular compound plastic products caused by talc can be qualitatively reflected. The products with low wet whiteness make the molecular compound plastics darken greatly. It is worth noting that the wet whiteness of talc with high dry whiteness is not necessarily high. Generally speaking, only talc with high purity and whiteness has high wet whiteness, that is to say, the degree of color darkening of molecular compound plastic products is less. The talcum powder used in the molecular compound plastics industry mainly has wet whiteness and hue, y and L * should be as high as possible, and the absolute values of a * and B * should be as small as possible. The wet whiteness of some products from the main talc deposits in Liaoning, Shandong and Guangxi can reach more than 70%. This part of products are mainly exported, and the domestic demand is not large. Of course, white talc is good, but the price is also high. In recent years, the price of Chinese white talc has been rising rapidly because the supply does not meet the demand. With the further growth of talc demand in molecular compound plastics industry, the situation of short supply will be aggravated. The scarcity of talc in the world is not temporary. The short supply will be a long-term situation in the future, and there is no possibility of reversal. Therefore, low whiteness talc should be used as far as possible. In fact, in many applications, there is no need for talc. The use of white talc is actually a waste. For example, in dark molecular compound plastics, there is no difference between high whiteness talc and low whiteness talc. The results show that the plastic whiteness of the final product increases by only 0.2-0.3 degree when the wet whiteness of talc increases by 1 degree. It is meaningless to pursue the whiteness of talc. In the past, due to the low price of high-grade white talc in China, many users did not consider using appropriate grade white talc too much, but the whiter the better. With the further increase of the price of talc, it is necessary to change our thinking and view. Trifoliation The remarkable strengthening effect of Talc on molecular compound plastic products is mainly due to its unique micro sheet structure. The more complete the talc sheet structure is, the more obvious the strengthening effect is. The two main factors that affect the flake of products are: the purity of talc, the processing essentials and skills of powder. The impurities in talc have no lamellar structure. The more pure talc is, the less impurity is, and the better lamellar structure is. In the process of micromachining products, different processing methods are used to keep the sheet structure of products. Improper essentials and processing technology will even crush its sheet structure. At present, the micro talc mainly adopts the air flow crushing technology, which includes two kinds of processing technology: the opposed flow method and the swirling flow method. Four fineness Micronization is the development trend of talc products. The finer the product is, the better the strengthening effect is. But at the same time, the surface energy of particles increases, which makes it easy to agglomerate, difficult to separate, and the price is also high. Therefore, we need to choose products with appropriate fineness according to our own skill level and practical needs, and there is no need to be as fine as possible. |